More realistic torpedo failures via SH3 Commander

Magic1111 · 11-27-09, 05:26 AM

Thanks for this MOD!

I will test it, when I am back from patrol and in port !

Best regards,
Magic

JScones · 11-27-09, 05:34 AM

Nice. It's always good to see stuff like this made by the community.

I don't have S3D or Mini Tweaker installed or I'd give you the torpedo.sim hex offsets...but I'm sure someone can assist.

LGN1 · 11-27-09, 06:12 AM

Hi,

thanks for the kind words. I have found out that in GWX and NYGM the TIII torpedo (which solved the depth problem) becomes available on the 1st of June 1942. Therefore I have changed the date entries above (new end date 19420531 instead of 19421031).

The TIII is already available earlier, but only as prototype and thus, cannot be chosen by the player (but some are given in the initial loadout). So, the torpedoes affected are the TI, TII, and, TIII. For these torpedos one should change the depth in the torpedo.sim file. I will try to figure out how this also can be done via SH3 Commander.

Cheers, LGN1

Magic1111 · 11-27-09, 06:26 AM

Quote:

Originally Posted by LGN1

I will try to figure out how this also can be done via SH3 Commander.

Cheers, LGN1

Oh yes, that would be good if that were possible!

Best regards,
Magic

JScones · 11-27-09, 06:33 AM

It's definitely possible. IIRC Mini Tweaker will give you the offset in hex. I'm not sure about S3D, but even if it gives the offset in decimal, it's simple to convert it to hex.

LGN1 · 11-27-09, 07:13 AM

I think I figured it out

In order to do the changes in the torpedo.sim file automatically, one has to add the following lines to Randomised events.cfg:

;----------Adapt initial depth in data\Library\Torpedo.sim for TI,TII,TIII begin----
[0:data\Library\Torpedo.sim]
ApplyToPeriod=19390101|19420531
;Or 19390101|19450508 for whole war
;No randomization
ChooseFrom=1
RndMidPat=1

0_x0CCF=2 ; initial depth for TI
0_x0E7B=2 ; initial depth for TII
0_x0FE7=2 ; initial depth for TIII
;----------Adapt launch depth in data\Library\Torpedo.sim for TI,TII,TIII end----

I would be very happy if someone who knows more about these values than I do could confirm them. It seems they are correct for stock SH3, GWX and NYGM (at least an older version. I don't know whether the file has been changed since then). So, if one uses a modified Torpedo.sim file then it is good to check these values again.

Cheers, LGN1

Sailor Steve · 11-27-09, 12:55 PM

This is brilliant! Can't wait until I can play again, so I can try it out.

11-27-09, 05:26 AM	#1
Magic1111 Silent Hunter Join Date: Sep 2008 Location: Germany - Sailing on U-552 in North Atlantic Posts: 4,429 Downloads: 783 Uploads: 0	Thanks for this MOD! I will test it, when I am back from patrol and in port ! Best regards, Magic __________________

11-27-09, 06:12 AM	#3
LGN1 Ace of the Deep Join Date: Mar 2006 Posts: 1,138 Downloads: 147 Uploads: 12	Hi, thanks for the kind words. I have found out that in GWX and NYGM the TIII torpedo (which solved the depth problem) becomes available on the 1st of June 1942. Therefore I have changed the date entries above (new end date 19420531 instead of 19421031). The TIII is already available earlier, but only as prototype and thus, cannot be chosen by the player (but some are given in the initial loadout). So, the torpedoes affected are the TI, TII, and, TIII. For these torpedos one should change the depth in the torpedo.sim file. I will try to figure out how this also can be done via SH3 Commander. Cheers, LGN1 Last edited by LGN1; 12-02-09 at 11:55 AM.

11-27-09, 07:13 AM	#6
LGN1 Ace of the Deep Join Date: Mar 2006 Posts: 1,138 Downloads: 147 Uploads: 12	I think I figured it out In order to do the changes in the torpedo.sim file automatically, one has to add the following lines to Randomised events.cfg: ;----------Adapt initial depth in data\Library\Torpedo.sim for TI,TII,TIII begin---- [0:data\Library\Torpedo.sim] ApplyToPeriod=19390101\|19420531 ;Or 19390101\|19450508 for whole war ;No randomization ChooseFrom=1 RndMidPat=1 0_x0CCF=2 ; initial depth for TI 0_x0E7B=2 ; initial depth for TII 0_x0FE7=2 ; initial depth for TIII ;----------Adapt launch depth in data\Library\Torpedo.sim for TI,TII,TIII end---- I would be very happy if someone who knows more about these values than I do could confirm them. It seems they are correct for stock SH3, GWX and NYGM (at least an older version. I don't know whether the file has been changed since then). So, if one uses a modified Torpedo.sim file then it is good to check these values again. Cheers, LGN1 Last edited by LGN1; 11-28-09 at 04:46 AM.

11-27-09, 12:55 PM	#7
Sailor Steve Eternal Patrol Join Date: Nov 2002 Location: High in the mountains of Utah Posts: 50,369 Downloads: 745 Uploads: 249	This is brilliant! Can't wait until I can play again, so I can try it out. __________________ “Never do anything you can't take back.” —Rocky Russo

11-27-09, 05:34 AM	#2
JScones Navy Seal Join Date: Apr 2005 Posts: 5,501 Downloads: 19 Uploads: 0	Nice. It's always good to see stuff like this made by the community. I don't have S3D or Mini Tweaker installed or I'd give you the torpedo.sim hex offsets...but I'm sure someone can assist.

11-27-09, 06:33 AM	#5
JScones Navy Seal Join Date: Apr 2005 Posts: 5,501 Downloads: 19 Uploads: 0	It's definitely possible. IIRC Mini Tweaker will give you the offset in hex. I'm not sure about S3D, but even if it gives the offset in decimal, it's simple to convert it to hex.