[WIP] Damage Control analyzer that factors crew experience into the damage report

[billko]

Originally Posted by Javelin

Using 1.1 and now every time I open the analyzer I get this message:

Unhand led exception has occurred in your application. If you click continue the application will ignore this error and attempt to continue. If you Quit, it will close.

Start index cannot be larger than the length of string. Parameter name: Startindex. Also mentions something about a JIT DebTo enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.

Any help will be appreciated. BTW I'm using TM overhauled.

I've been thinking about what you said. You said that this happens as soon as you launch DC?

Have you tried uninstalling and then re-installing DC? It sounds like something got corrupted.

Bill

[Javelin]

[quote=billko]

Originally Posted by Javelin

Using 1.1 and now every time I open the analyzer I get this message:

Unhand led exception has occurred in your application. If you click continue the application will ignore this error and attempt to continue. If you Quit, it will close.

Start index cannot be larger than the length of string. Parameter name: Startindex. Also mentions something about a JIT DebTo enable just-in-time (JIT) debugging, the .config file for this
application or computer (machine.config) must have the
jitDebugging value set in the system.windows.forms section.
The application must also be compiled with debugging
enabled.
For example:
<configuration>
<system.windows.forms jitDebugging="true" />
</configuration>
When JIT debugging is enabled, any unhandled exception
will be sent to the JIT debugger registered on the computer
rather than be handled by this dialog box.

Any help will be appreciated. BTW I'm using TM overhauled.

I've been thinking about what you said. You said that this happens as soon as you launch DC?

Have you tried uninstalling and then re-installing DC? It sounds like something got corrupted.
Yes I have and with the same results.

[billko]

[quote=Javelin]

Originally Posted by billko

I've been thinking about what you said. You said that this happens as soon as you launch DC?

Have you tried uninstalling and then re-installing DC? It sounds like something got corrupted.
Yes I have and with the same results.

The error means that it read an empty string and it's trying to grab a piece of that string at a certain position in that string. Since the length is zero, it causes the error.

If there was more to the error, could you post everything before that long-winded speech about JIT debugger? And it happens as soon as the application opens, right?

Thanks a bunch!

Bill

[Javelin]

I don't know how or why, but the Analyzer is now working. Made no changes to either it or SH4. Only change to this computer in the past few days is I repaired Microsoft's Flight Simulation Acceleration. Go figure.

[billko]

Originally Posted by Javelin

I don't know how or why, but the Analyzer is now working. Made no changes to either it or SH4. Only change to this computer in the past few days is I repaired Microsoft's Flight Simulation Acceleration. Go figure.

As long as it works! :hmm: Maybe it was a registry error that got fixed when you repaired MFSA. DC does look at the registry to determine where you installed SH4 and if it couldn't find the key it would return an empty string that would cause your error upon starting DC.

Bill

[Frank Smith]

Can some one direct me to a actual DL site for Damage Analyzer.
the link only takes me to BlueSky.
Links to any working Damage Analyzer for SH4 is appreciated.

Snuffy Smith

[billko]

Originally Posted by Frank Smith

Can some one direct me to a actual DL site for Damage Analyzer.
the link only takes me to BlueSky.
Links to any working Damage Analyzer for SH4 is appreciated.

Snuffy Smith

Frank:

Hmmm, when i click the link it brings me to the subsim download area where it now resides. However, since it doesn't matter where the link brings ME, here is a link to the download page:

http://www.subsim.com/radioroom/down...o=file&id=1156

If this fails, simply go to the subsim download area and look it up under "Utilities."

Good luck!!!

Bill

[Frank Smith]

Thank you very much. I assume some links do not work correctly due to BETA test of Windows 7.
Your link worked.
Thanks much

[billko]

De nada.

[Gregn2484]

I didn't look through this whole thread, so forgive me for asking but, does this work with SH4.1.5?

[billko]

Originally Posted by Gregn2484

I didn't look through this whole thread, so forgive me for asking but, does this work with SH4.1.5?

I believe it does, but since they "re-fixed" the medals fiasco, the medals in the app may not match the medals in the game.

[gar]

I downloaded from the subsum site and when I run the setup program it responds with a message that an error occurred while attempting to installl. I have clicked on the Bluesky site and received a broken link message. Can Someone please direct me to a location with a working download. - Thanks in advance, Garry

[billko]

Originally Posted by gar

I downloaded from the subsum site and when I run the setup program it responds with a message that an error occurred while attempting to installl. I have clicked on the Bluesky site and received a broken link message. Can Someone please direct me to a location with a working download. - Thanks in advance, Garry

Gar, your message is confusing. Did you actually download it or just click on the link? Please see post #142 and let me know if it worked.

Thanks!

[Frank Smith]

does any body have a full woring version of any of the Damage Control Analyzer. even the original or the v 1.0 (see pic on page 1).
sorry for asking for old but my HDD crashed and even with the (save) and recovery of 4 CDs full of SH4. I have no Damage Control. which I feel actually added to the SUB program...
Thanks...
@Billko for what you found. but SETUP is not complete.

Thanks

[billko]

Originally Posted by Frank Smith

does any body have a full woring version of any of the Damage Control Analyzer. even the original or the v 1.0 (see pic on page 1).
sorry for asking for old but my HDD crashed and even with the (save) and recovery of 4 CDs full of SH4. I have no Damage Control. which I feel actually added to the SUB program...
Thanks...
@Billko for what you found. but SETUP is not complete.

Thanks

Hi, Frank - I just emailed you an uncorrupted version of the zip that contains everything.

Also, I added the file to the Damage Control Download Area!