Mine Detection?

[sonar732]

Originally Posted by Kojo62

Ahoy fellow Skippers. I was wondering if anyone could give me some tips on Mine detection and avoidance techniques?

I was on the stock mission in the Strait of Hormuz where you deploy one Seal team, then recover another, and negligently ran into a mine in between the two ops. I didn't even know there were mines to be found in this strait, and I'd like to find out what I should've done to avoid this fate.

I read in the manual that High Frequency sonar is what should be used to locate mines. But isn't that an active sonar mode? Is there any way to employ this with passive? Pinging away in this region does not strike me as a good choice, given that my orders are to remain undetected. So I'm confused here.

From the Sub Command manual...

Originally Posted by Sub Command Manual pg.150

UUVs are in passive mode when launched. However, active sonar may be necessary when
traversing a minefield. Be aware that capable ships and subs in the area can detect UUV active
sonar.

Follow these steps to enable UUV active sonar.
1. Enable the wire guide controls for the UUV as described above.
2. Click ENABLE to initiate active sonar.
3. Click PRE-ENABLE to de-activate active sonar and return to passive mode.

[Kojo62]

Originally Posted by sonar732

From the Sub Command manual...

Yes, I did read the manual on that topic after my failure. But sorry, I'm am not totally clear on how the highlighted passage addresses my question. As I asked originally, where my dillemma lies is that:

1) I didn't even know to expect mines in that area beforehand. They were not part of my orders.
2) Hi-frequency being a mode of active sonar would potentially alert other vessels to my presence there, when my orders are to stay undetected.

So I'm asking:

1) If there's a routine I should adopt to ascertain the presence of mines in all my regular operating cirumstances?
2) How can I do so and avoid detection at the same time?

Are you suggesting Sonar732 that I should always launch a UUV to sweep for mines before proceeding with any mission?

Or, as Pisces suggests, is it relatively safe to just go ahead and use hi-freq because it is short range? But even then, how do I know when I should use it, especially if I have no prior warning of potential mines in the area?

Seems like a catch-22 to me, so I figure I must be missing something.

[DrMilton]

Originally Posted by Kojo62

2) Hi-frequency being a mode of active sonar would potentially alert other vessels to my presence there, when my orders are to stay undetected.

As you probably didn't understand Pisces' reply I will reemphasize: HF sonar CANNOT be detected in SC. In real life yes but NOT in the game, so go ahead and use it.

UUV is a valuable tool in getting situational and positional awareness but WHEN and IF the conditions are proper. When are they proper? Thats for you to decide according to your information and skill. No one will give you a premade answer because there is not one. If you estimate that there is noone around to hear you, active UUV will spot the mines for you. If you 're not sure then you don't use it. Usually, intel should warn you about minefields but not always (life is tough...) so the routine for just about every decision you make (not just mines) will be from carefull to suspicious to paranoid. No ready answers.

[Kojo62]

Thanks DrMilton. I did understand Pisces answer, although I didn't quite understand what else Sonar732 was trying to tell me beyond what I'd read in the manual.

I guess I was hoping that maybe being a noob, I'd just failed to employ some standard proecedure that all the vets here would already know to do every time you take your boat out. But it doesn't sound like I'll find that obvious an answer. More like I just ran into a tough break by not expecting the mines where I found them ... although I know my C.O. would not accept that as an excuse ... nor do I.

Whatever the reason, I failed ... period. Like you said ... life is tough ...

Thanks again for your tips, folks.

[sonar732]

The Straights of Hormuz has terrible sonar dynamics. If I remember right, there is a small area of deep water. This is where you would launch your UUV and make the depth 100 feet.

I just did a quick test on this mission and when you raise all of your mast, the radio mast states that Iranian mine layers have returned to port empty. Also, I launched the UUV and detected nothing at first until it went a little farther to find a group of mines. No counter-detection message or anything which supports my theory of the straights being bad sonar dynamics.

[Monica Lewinsky]

Kojo62,

An online educational tutorial to avoid mines, here you go :
http://sikvid.com/ext-media.php?go=5726

game over!

[Stanny]

High frequency active sonar is always the most effective way for mine detection.You turn it on and simply navigate watching for mine shape objects on the display.It is quite easy,actually.It is also very useful for under ice operations and crucially needed when surfacing under ice as helps you to avoid underwater icebergs.