Gwen's Arkmodel 1/48 scale RC Type VIIC build log - Page 5

Gwenydd · 12-19-22, 07:39 PM

Quote:

Originally Posted by Onkel Neal

Wow, that's cool, Gwen. Something I would never do, I don 't like heights

I love to fly. I first soloed when I was sixteen back in Ohio. I was lucky enough to be friends with a National Guard helicopter pilot who was also a flight instructor and he taught me.

Gwenydd · 12-20-22, 02:33 AM

Quote:

Originally Posted by ET2SN

Woo... OK, I'm trying to avoid a reply that looks like a twelve paragraph thesis.

For the record, I have ZERO experience with bow planes. Both of the boats I was on ran fairwater planes and fairwaters don't effect trim, they only provide linear up/down movement.

Anyway, when the boat is on the surface (rigged for surface) the planes tend to get locked at a certain amount of upward trim. This makes the hull more efficient in terms of how it planes through the water. In other words, you want the bow to be riding high. When you dive, you want the boat to remain mostly level. I was wondering if you could program your planes for a surfaced condition?

Ah I see what you mean. I don't need to worry about that. My boat is set up so that the forward dive planes are used to primarily control depth and the rear dive planes to primarily control the pitch of the boat. Each set of planes has a controller board connected to the servos for it. The aft plane controller board automatically controls the planes to keep the boat in a level attitude unless I override it with control inputs. While the forward plane controller board uses a barometric pressure sensor connected to a hose that samples outside water pressure. The board automatically controls the forward planes to hold the depth last commanded with the forward plane controls.

If you look at the waterline on the type VII U-boat you see that the bow is naturally riding a bit high when the waterline on the boat matches the actual waterline - and that is the pitch level the aft planes will seek.

Makes sense?

PS - Hope you enjoyed my test flight videos.

Kapt Z · 12-25-22, 06:30 PM

Quote:

Originally Posted by Gwenydd

I love to fly. I first soloed when I was sixteen back in Ohio. I was lucky enough to be friends with a National Guard helicopter pilot who was also a flight instructor and he taught me.

What fun! I love flying, but never found time, money...etc to get my license.

How is that plane designated? Experimental?

Gwenydd · 12-26-22, 09:11 PM

Quote:

Originally Posted by Kapt Z

What fun! I love flying, but never found time, money...etc to get my license.

How is that plane designated? Experimental?

It's an experimental category aircraft since I built it myself. =) It does require a pilot's license and a fair bit of experience to fly.

Aktungbby · 12-26-22, 09:20 PM

Do U pack your own parachute?

Gwenydd · 12-27-22, 07:06 PM

Quote:

Originally Posted by Aktungbby

Do U pack your own parachute?

No parachute, just me and the airplane.

ET2SN · 01-06-23, 04:42 AM

Quote:

Originally Posted by Gwenydd

No parachute, just me and the airplane.

Don't forget Gravity..

iceno9 · 01-05-24, 03:25 PM

Gwen - I am just about to start a build of the Arkmodel 1:48 U-boat. I would like to know more about your WTC design. For example, is there a reason you chose 3" rather than 3.5" which would have allowed 2x side by side motors rather than the one with power......it looks like 3.5" will fit, but maybe shorter length than a 3" one.

Is there a way i can message you some more questions/thoughts?

Thanks

Aktungbby · 01-05-24, 08:49 PM

iceno9!

Gwenydd · 08-14-24, 04:18 AM

Quote:

Originally Posted by iceno9

Gwen - I am just about to start a build of the Arkmodel 1:48 U-boat. I would like to know more about your WTC design. For example, is there a reason you chose 3" rather than 3.5" which would have allowed 2x side by side motors rather than the one with power......it looks like 3.5" will fit, but maybe shorter length than a 3" one.

Is there a way i can message you some more questions/thoughts?

Thanks

Hey, I apologize for not replying sooner. I haven't been on the forums for some time . I can say for sure that a 3.5" WTC will not fit in the Arkmodel hull. It's a tight fit for a 3" cylinder. And sure, you can send me pm's here on the forum or I can give you my email address if you prefer.

Gwen

Aktungbby · 08-14-24, 09:35 AM

Gwenydd!

...after a nearly 2-year silent run!

Gwenydd · 08-14-24, 10:21 AM

Still alive... sorta...

... and call me Gwen =)

Onkel Neal · 08-17-24, 08:02 AM

Good to hear, we'll call off the search parties

Gwenydd · 08-17-24, 06:27 PM

hehe, glad to know somebody cares =)

12-26-22, 09:20 PM	#65
Aktungbby Gefallen Engel U-666 Join Date: Jul 2013 Location: On a tilted, overheated, overpopulated spinning mudball on Collision course with Andromeda Galaxy Posts: 29,979 Downloads: 24 Uploads: 0	Do U pack your own parachute? __________________ "Only two things are infinite; The Universe and human squirrelyness?!!

01-05-24, 08:49 PM	#69
Aktungbby Gefallen Engel U-666 Join Date: Jul 2013 Location: On a tilted, overheated, overpopulated spinning mudball on Collision course with Andromeda Galaxy Posts: 29,979 Downloads: 24 Uploads: 0	welcome aboard! iceno9! __________________ "Only two things are infinite; The Universe and human squirrelyness?!!

08-14-24, 09:35 AM	#71
Aktungbby Gefallen Engel U-666 Join Date: Jul 2013 Location: On a tilted, overheated, overpopulated spinning mudball on Collision course with Andromeda Galaxy Posts: 29,979 Downloads: 24 Uploads: 0	Welcome back! Gwenydd!...after a nearly 2-year silent run! __________________ "Only two things are infinite; The Universe and human squirrelyness?!!

08-14-24, 10:21 AM	#72
Gwenydd verrückt kaleun Join Date: Nov 2014 Location: Northwestern Washington Posts: 104 Downloads: 148 Uploads: 3	Still alive... sorta... ... and call me Gwen =) __________________ Gwen

08-17-24, 08:02 AM	#73
Onkel Neal Born to Run Silent Join Date: Jan 1997 Location: Cougar Trap, Texas Posts: 21,383 Downloads: 541 Uploads: 224	Good to hear, we'll call off the search parties __________________ SUBSIM - 26 Years on the Web

01-05-24, 03:25 PM	#68
iceno9 Cadet Join Date: Jan 2024 Posts: 1 Downloads: 0 Uploads: 0	Gwen - I am just about to start a build of the Arkmodel 1:48 U-boat. I would like to know more about your WTC design. For example, is there a reason you chose 3" rather than 3.5" which would have allowed 2x side by side motors rather than the one with power......it looks like 3.5" will fit, but maybe shorter length than a 3" one. Is there a way i can message you some more questions/thoughts? Thanks

08-17-24, 06:27 PM	#74
Gwenydd verrückt kaleun Join Date: Nov 2014 Location: Northwestern Washington Posts: 104 Downloads: 148 Uploads: 3	hehe, glad to know somebody cares =) __________________ Gwen