SUBSIM: The Web's #1 resource for all submarine & naval simulations since 1997 |
04-22-19, 07:29 AM | #1 |
Nub
Join Date: Apr 2019
Posts: 4
Downloads: 9
Uploads: 0
|
Ahnenerbe 1920x1080
Ok so I've got the Ahnenerbe 1920 x1080 GUI on SHIII and it's really good, I really like it. However, before that I had one of the sub interior mods which allow you to freeroam around the inside of the sub (engine etc) - however the new widescreen GUI is incompatible with it which is a shame - anyone know how I can use both the 1920x1080 GUI and have a sub interior too?
|
04-22-19, 08:23 AM | #2 |
not dead yet
Join Date: May 2017
Location: Romania
Posts: 193
Downloads: 130
Uploads: 1
|
FM_NewInterior v2.1D works fine with Ahnenerbe Widegui mod .
|
04-22-19, 01:32 PM | #3 |
Nub
Join Date: Apr 2019
Posts: 4
Downloads: 9
Uploads: 0
|
Yes, I've got that, it doesn't work for me - it just crashes if I enable in whilst Ahnenerbe is enabled.
|
04-22-19, 03:35 PM | #4 |
not dead yet
Join Date: May 2017
Location: Romania
Posts: 193
Downloads: 130
Uploads: 1
|
With NYGM works fine and i think it should work with GWX also, i think i saw others using it . Ahnenerbe should be installed last .
|
04-27-19, 01:47 PM | #5 | |
Stowaway
Posts: n/a
Downloads:
Uploads:
|
Quote:
4GB patch is also highly recommended to make sure the game has enough memory for those rather large mods. |
|
05-04-19, 09:55 AM | #6 | |
Seaman
Join Date: May 2005
Location: Atlanta, GA
Posts: 38
Downloads: 97
Uploads: 0
|
Quote:
This. After returning to SH3 after a long hiatus and having to load everything again, including GWX Gold and Ahnenerbe 1920x1080, the 4GB patch was a must have for everything to run together correctly. |
|
05-05-19, 05:37 AM | #7 |
Nub
Join Date: Apr 2019
Posts: 4
Downloads: 9
Uploads: 0
|
Thank you Mussalo and Lannes - the 4gb has sorted it, seems its a must for mods.
|
05-05-19, 11:56 AM | #8 |
Gefallen Engel U-666
|
Welcome aboard!
Broomwagon!
__________________
"Only two things are infinite; The Universe and human squirrelyness; and I'm not too sure about the Universe" |
05-07-19, 02:14 AM | #9 |
Stowaway
Posts: n/a
Downloads:
Uploads:
|
Ahnenerbe Widegui mod
Recently downloaded Ahnenerbe Widegui Final mod and it has d3d9.dll & d3d9 config files but seems to be missing the d3d9.ini file because it will not load.
Where can I find this d3d9.ini file? |
05-07-19, 04:03 AM | #10 |
Growing Old Disgracefully
|
Hi vZ
When you unzip the downloaded file the mod folder you are looking at when enabled will put the 2 d3d9 files in your main game folder. Peter
__________________
LSH3-2015 <> TUTORIALS <> ALL YOU NEED TO KNOW <> ALL IN ONE PLACE SH4 <> TUTORIALS <> HOW TO DO IT <> INFORMATION <> DOWNLOAD LINKS SH5 <> TUTORIALS <> HOW TO DO IT <> INFORMATION <> DOWNLOAD LINKS Always Here To Help A Fellow 'Subber' | Need An Answer to A Question Just Send Me A PM |
05-07-19, 10:13 AM | #11 |
Stowaway
Posts: n/a
Downloads:
Uploads:
|
Missing file error previously; I will try again.
|
05-08-19, 11:12 AM | #12 |
Stowaway
Posts: n/a
Downloads:
Uploads:
|
As promised, I re-installed Ahnenerbe Widegui Final mod with the generic mod enabler to stock SH3, as before. It includes two files, d3d9.dll & d3d9 (a config file apparently). Both files positively installed within the SH3 directory.
Initialize game with SH3 Commander and the resulting error message appeared: "Can not initialize 3D engine" Removed both d3d9 files, and then removed them individually; and restarted SH3. Game boots up all three ways with the mod but I could tell that the screen was cut off along the top and on the right side making it unplayable. But, the mod did install. I changed screen ratios with all available ratios (7 of them) on my laptop from 1366 x 768 to 800 x 600 and also changed between "maintain aspect ratio", "scale full screen" & "center image". Result: Mod does not work on my setup. Any suggestions? |
05-08-19, 01:06 PM | #13 | |
Ocean Warrior
|
Quote:
__________________
"Realistic" is not always GAME-GOOD." - Wave Skipper |
|
05-08-19, 01:22 PM | #14 |
Growing Old Disgracefully
|
A Warm Welcome To The Subsim Community > Broomwagon
Subsim <> Make A Donation <> See The Benefits <> Support The Community SH3 – 4 - 5 Tutorials > Downloads > Other Useful Information > See Links in My Signature Below
__________________
LSH3-2015 <> TUTORIALS <> ALL YOU NEED TO KNOW <> ALL IN ONE PLACE SH4 <> TUTORIALS <> HOW TO DO IT <> INFORMATION <> DOWNLOAD LINKS SH5 <> TUTORIALS <> HOW TO DO IT <> INFORMATION <> DOWNLOAD LINKS Always Here To Help A Fellow 'Subber' | Need An Answer to A Question Just Send Me A PM |
05-08-19, 01:34 PM | #15 | |
Growing Old Disgracefully
|
Hi vZ
Quote:
Make sure your gpu is setup correctly. Post #7 Changing Nvidia And AMD Radeon GPU Settings > Pictorial SH3 also needs to be setup correctly. Installation instructions for Ahnenerbe's mod Post #42 Changing Any LSH3-2015 Gui To > Ahnenerbe WideGui 1920 x 1080 Final > Download And Instructions > Enable JSGME > Pictorial You also might need to use this fix. Post #59 Override High DPI Scaling Behavior Graphic Fix > Pictorial Peter
__________________
LSH3-2015 <> TUTORIALS <> ALL YOU NEED TO KNOW <> ALL IN ONE PLACE SH4 <> TUTORIALS <> HOW TO DO IT <> INFORMATION <> DOWNLOAD LINKS SH5 <> TUTORIALS <> HOW TO DO IT <> INFORMATION <> DOWNLOAD LINKS Always Here To Help A Fellow 'Subber' | Need An Answer to A Question Just Send Me A PM |
|
|
|