Modern TV sound options very poor!

Reece · 01-19-11, 06:35 PM

Quote:

Originally Posted by longam

That's basically what I do, just use the TV as a hub and run a single out to the external amp, no more swapping what I want to listen to. I did have to disable the TV speakers and enable the output, but they were crap anyway.

In the manual there is part of the menu selection as follows:

Speaker Select (External Speaker / TV Speaker)
A sound echo may occur due to a difference in decoding
speed between the main speaker and the audio receiver. In
this case, set the TV to External Speaker.
When Speaker Select is set to External Speaker, the
volume and MUTE buttons will not operate and the
sound settings will be limited.

So you might be right Wim, though I haven't worked out how to get to this yet but when I do I will give it a try, you need a pilots license to operate this!

Hakahura · 01-19-11, 08:38 PM

I remember back when I got my Blu Ray player and hooked it up to my DTS amp...

Connected using an optical cable and no matter what I played or tried the sound was terrible and definitly not DTS or 5.1.

Then I read the amps manual

I had to tell the amp and configuer the input the Blu Ray was going through, that the input was now optical, the default setting was coaxial.

Ever since all has been fine.

Any help?

Reece · 01-19-11, 09:08 PM

No but thanks, the optical connection works fine but only in "TV" mode, playing any other device comes out the TV and not the TV audio out!!

Reece · 01-21-11, 10:19 PM

Well I finally got to go through the menu and there is absolutely no settings that will overcome this problem, setting "Speaker Select" to external still only plays the TV's sound, not other units plugged into it, so it looks like I will have to take the audio from each unit to the amplifier and have to select the appropriate one!

What a shuffle game!!

longam · 01-22-11, 08:14 PM

From my blue ray player I only use a HDMI cable, no audio cables needed casue it all goes threw HDMI. Maybe the is causing you echo effect trying to use both? But of course if you TV does not pass threw the sound to the amp...

I'll have to post a picture sometime of all the remotes I have on my end table to run all my stuff. Universals only do so much function wise so you need the original remote. Looks like a parking lot.

Reece · 01-23-11, 07:14 AM

Quote:

Originally Posted by longam

From my blue ray player I only use a HDMI cable, no audio cables needed casue it all goes threw HDMI. Maybe the is causing you echo effect trying to use both? But of course if you TV does not pass threw the sound to the amp...

I'll have to post a picture sometime of all the remotes I have on my end table to run all my stuff. Universals only do so much function wise so you need the original remote. Looks like a parking lot.

I know what you mean I have 6!!

Gerald · 01-23-11, 07:16 AM

Quote:

Originally Posted by Reece

I know what you mean I have 6!!

The number six is perfect for you,

01-19-11, 08:38 PM	#2
Hakahura Grey Wolf Join Date: Aug 2006 Location: The United Kingdom of Great Britain and Northern Ireland Posts: 785 Downloads: 0 Uploads: 0	I remember back when I got my Blu Ray player and hooked it up to my DTS amp... Connected using an optical cable and no matter what I played or tried the sound was terrible and definitly not DTS or 5.1. Then I read the amps manual I had to tell the amp and configuer the input the Blu Ray was going through, that the input was now optical, the default setting was coaxial. Ever since all has been fine. Any help? __________________ Sir Humphey Appleby, GCB, KBE, MVO and MA. Britain's Greatest Orator, well bar that Churchill fellow.

01-19-11, 09:08 PM	#3
Reece CINC Pacific Fleet Join Date: Sep 2003 Location: Down Under Posts: 34,771 Downloads: 171 Uploads: 0	No but thanks, the optical connection works fine but only in "TV" mode, playing any other device comes out the TV and not the TV audio out!! __________________ *Sub captains go down with their ship!*

01-21-11, 10:19 PM	#4
Reece CINC Pacific Fleet Join Date: Sep 2003 Location: Down Under Posts: 34,771 Downloads: 171 Uploads: 0	Well I finally got to go through the menu and there is absolutely no settings that will overcome this problem, setting "Speaker Select" to external still only plays the TV's sound, not other units plugged into it, so it looks like I will have to take the audio from each unit to the amplifier and have to select the appropriate one! What a shuffle game!! __________________ *Sub captains go down with their ship!*

01-22-11, 08:14 PM	#5
longam Admiral Join Date: Jun 2005 Posts: 2,014 Downloads: 26 Uploads: 0	From my blue ray player I only use a HDMI cable, no audio cables needed casue it all goes threw HDMI. Maybe the is causing you echo effect trying to use both? But of course if you TV does not pass threw the sound to the amp... I'll have to post a picture sometime of all the remotes I have on my end table to run all my stuff. Universals only do so much function wise so you need the original remote. Looks like a parking lot.