SOLUTION FOR "The Load Failure with No Error"

StarLion45 · 07-24-08, 03:03 AM

Hello everyone !
Have you played SH3 and sunk a lot of ships , and you think for your self that this is the BIG ONE? yeah me too.
But,,,Heyy , suddently a popup appears on the screen sayin "Load Failure with No Error" , and you get CTD

And you must start the whole thing all over again.
THAT IS VERY ANNOYING BELIEVE YOU ME.

At least I have get my SH3 working great

The speed on my pc is not so fast , but I can play my SH3 game normally , and that is the most important thing isn't it!?!
The solution did I find in a discussforum , but I don't remeber where .
Here is the post that gave me just what I need :

" Ok everyone , I have the solution for the "Load Failure with No Error".
There is in fact an error and it has to do with memory.

Here is the fix:

FIRST LOCATION :
" Right-click your SH3 icon on your desktop ( the one you would normally double-click to launch the game , and the SH3Cmdr too)
Then click " properties", click the shortcut tab.
In the line labeled " Target ", you will see something like this , depending on where you put the program when you installed it" :

"C:\ProgramFiles\Ùbisoft\Sh3.exe "etc
-------------------------------------
Copy and paste the following AFTER the above line :

"+mat_forcehardwaresync 0 +snd_async_prefetch_priority 1 "
------------------------------------------------------------
BE SURE THERE IS A SPACE BETWEEN Exe and +mat!!!!!!!!!!!!
Click save and you are ready to go.
THAT'S IT!!

GOOD LUCK EVERYONE

mcf1 · 07-24-08, 04:33 AM

I never had this problem, but thanks I'll keep it in mind.
And by the why, is it only for stock SH3?

StarLion45 · 07-24-08, 04:53 AM

just do it on SH3Cmdr and SH3 with GWX 2.0 & 2.1

mcf1 · 07-24-08, 05:12 AM

OK then.
Thanks again

coronas · 07-24-08, 05:21 AM

Quote:

Originally Posted by StarLion45

just do it on SH3Cmdr and SH3 with GWX 2.0 & 2.1

It's valid for other mods (WAC, NGYM, etc)?
Thanks for sharing!

StarLion45 · 07-24-08, 06:21 AM

It's valid for other Mods too

you know if it works for Gwx etc then it is valid for the rest

GOOD LUCK

Cohaagen · 07-24-08, 06:52 AM

Um, I'm pretty sure these commands are for Half Life 2 only, because I remember using them when I had problems with Episode One. I'm almost certain they're Source Engine-specific and are graphics parameters, though the second one deals with the way the engine spools sounds from the hard disk into RAM.

Sorry, but I don't think this works.

07-24-08, 03:03 AM	#1
StarLion45 Grey Wolf Join Date: Mar 2008 Location: Stavanger,Norway Posts: 895 Downloads: 78 Uploads: 0	SOLUTION FOR "The Load Failure with No Error" Hello everyone ! Have you played SH3 and sunk a lot of ships , and you think for your self that this is the BIG ONE? yeah me too. But,,,Heyy , suddently a popup appears on the screen sayin "Load Failure with No Error" , and you get CTD And you must start the whole thing all over again. THAT IS VERY ANNOYING BELIEVE YOU ME. At least I have get my SH3 working great The speed on my pc is not so fast , but I can play my SH3 game normally , and that is the most important thing isn't it!?! The solution did I find in a discussforum , but I don't remeber where . Here is the post that gave me just what I need : " Ok everyone , I have the solution for the "Load Failure with No Error". There is in fact an error and it has to do with memory. Here is the fix: FIRST LOCATION : " Right-click your SH3 icon on your desktop ( the one you would normally double-click to launch the game , and the SH3Cmdr too) Then click " properties", click the shortcut tab. In the line labeled " Target ", you will see something like this , depending on where you put the program when you installed it" : "C:\ProgramFiles\Ùbisoft\Sh3.exe "etc ------------------------------------- Copy and paste the following AFTER the above line : "+mat_forcehardwaresync 0 +snd_async_prefetch_priority 1 " ------------------------------------------------------------ BE SURE THERE IS A SPACE BETWEEN Exe and +mat!!!!!!!!!!!! Click save and you are ready to go. THAT'S IT!! GOOD LUCK EVERYONE

07-24-08, 04:53 AM	#3
StarLion45 Grey Wolf Join Date: Mar 2008 Location: Stavanger,Norway Posts: 895 Downloads: 78 Uploads: 0	No just do it on SH3Cmdr and SH3 with GWX 2.0 & 2.1

07-24-08, 06:21 AM	#6
StarLion45 Grey Wolf Join Date: Mar 2008 Location: Stavanger,Norway Posts: 895 Downloads: 78 Uploads: 0	Yeees It's valid for other Mods too you know if it works for Gwx etc then it is valid for the rest GOOD LUCK

07-24-08, 04:33 AM	#2
mcf1 Seasoned Skipper Join Date: Oct 2007 Location: Greece, Volos Posts: 710 Downloads: 10 Uploads: 0	I never had this problem, but thanks I'll keep it in mind. And by the why, is it only for stock SH3?

07-24-08, 05:12 AM	#4
mcf1 Seasoned Skipper Join Date: Oct 2007 Location: Greece, Volos Posts: 710 Downloads: 10 Uploads: 0	OK then. Thanks again

07-24-08, 06:52 AM	#7
Cohaagen Frogman Join Date: Jul 2007 Location: UK Posts: 296 Downloads: 43 Uploads: 0	Um, I'm pretty sure these commands are for Half Life 2 only, because I remember using them when I had problems with Episode One. I'm almost certain they're Source Engine-specific and are graphics parameters, though the second one deals with the way the engine spools sounds from the hard disk into RAM. Sorry, but I don't think this works.