SOLUTION FOR "The Load Failure with No Error"
 

:lol: Hello everyone !
Have you played SH3 and sunk a lot of ships , and you think for your self that this is the BIG ONE? yeah me too.
But,,,Heyy , suddently a popup appears on the screen sayin "Load Failure with No Error" , and you get CTD:yep:
And you must start the whole thing all over again.
THAT IS VERY ANNOYING BELIEVE YOU ME.

At least I have get my SH3 working great:D
The speed on my pc is not so fast , but I can play my SH3 game normally , and that is the most important thing isn't it!?!
The solution did I find in a discussforum , but I don't remeber where .
Here is the post that gave me just what I need :

" Ok everyone , I have the solution for the "Load Failure with No Error".
There is in fact an error and it has to do with memory.

Here is the fix:

FIRST LOCATION :
" Right-click your SH3 icon on your desktop ( the one you would normally double-click to launch the game , and the SH3Cmdr too)
Then click " properties", click the shortcut tab.
In the line labeled " Target ", you will see something like this , depending on where you put the program when you installed it" :

"C:\ProgramFiles\Ùbisoft\Sh3.exe "etc
-------------------------------------
Copy and paste the following AFTER the above line :

"+mat_forcehardwaresync 0 +snd_async_prefetch_priority 1 "
------------------------------------------------------------
BE SURE THERE IS A SPACE BETWEEN Exe and +mat!!!!!!!!!!!!
Click save and you are ready to go.
THAT'S IT!!

GOOD LUCK EVERYONE:up:

I never had this problem, but thanks I'll keep it in mind.
And by the why, is it only for stock SH3?

No
 

:D just do it on SH3Cmdr and SH3 with GWX 2.0 & 2.1:lol:

OK then.
Thanks again:up:

It's valid for other mods (WAC, NGYM, etc)?
Thanks for sharing! :up:

Yeees
 

:D It's valid for other Mods too:)
you know if it works for Gwx etc then it is valid for the rest:lol:

GOOD LUCK:up:

Um, I'm pretty sure these commands are for Half Life 2 only, because I remember using them when I had problems with Episode One. I'm almost certain they're Source Engine-specific and are graphics parameters, though the second one deals with the way the engine spools sounds from the hard disk into RAM.

Sorry, but I don't think this works.

SOLUTION FOR " The load Failure With No error 2.
 

:D Hi there "Cohaagen"!
You are wrong!
you see I had this irritating popup on my screen a long time because my SH3 crashing almost all the time , see many of my early post .
Yes it's for "HALFLIFE 2" BUT NOT ONLY!!!
I am the living proof of that:lol: .
My game ( SH3 ) is now running smoothly , with no error popups , and it's stabile.
And it's a joy now to play SH3:yep:
I tryed to play SH3 early today without :

" +mat_forcehardwaresync 0 +snd_async_prefetch_priority 1 "
--------------------------------------------------------------
And suddently the annoying message popups again:damn:
and when I write that line in ; NO POPUPS!!!!
You see if you are fishing Trouts and Salmons , don't fish with the same stuff always, " SHOW THEM SOMETHING NEW " , my Grandfather told me :yep: :lol:
You do understand what I mean????


http://img300.imageshack.us/img300/3...otuboatrk6.jpg

Starlion
"+mat_forcehardwaresync 0 +snd_async_prefetch_priority 1 "

Is the above correct please -- quotation marks as well. If so should not the last " be nearer the figure 1 1"