Problems New Interiors

f6l913 · 06-03-11, 08:31 AM

I Have Problems with FM_NewInteriors v.1.0
Whenn i go in the Mashine Room and i change the Speed, the PC shut down> Bluescreen !?
And when i use the Periscope there is the same Problem, a Bluescreen and the PC goes Down.

Sorry for my bad english...

Wenn es hier Deutsche gibt,
Immer wenn ich in den Maschinenraum Gehe und die Geswindigkeit ändere Kommt ein Bluescreen und der komplette PC schmiert ab.
Zudem gibt es eine Möglichkeit durch die Shotten zu gehen, ich muss mich immer mit F2 darumarbeiten

Gerald · 06-03-11, 08:32 AM

Bakkels · 06-03-11, 09:04 AM

What are your system specs? Because FM Interior is quite a demanding mod. 3 or 4 gig memory is recommended for this one.

Also, there is a free camera mod so you don't have to press f2 when you want to walk around the ship, but I'm not exactly sure where I found it. Try searching the downloads section for that one.

Fish In The Water · 06-03-11, 11:07 AM

If you're running other (memory) 'heavy' mods, you might want to temporarily disable them and then try to replicate the issue with New Interiors.

Also, there are a number of 'fixes' available that make other mods compatible with NI, so you may want to check your mod list and see if there are any potential conflicts.

Aside from that, Bakkels is quite correct in suggesting you may need the 4 GB patch (along with the corresponding amount of RAM) in order to successfully run it.

Good luck!

06-03-11, 08:31 AM	#1
f6l913 Bilge Rat Join Date: Jun 2011 Posts: 1 Downloads: 3 Uploads: 0	Problems New Interiors I Have Problems with FM_NewInteriors v.1.0 Whenn i go in the Mashine Room and i change the Speed, the PC shut down> Bluescreen !? And when i use the Periscope there is the same Problem, a Bluescreen and the PC goes Down. Sorry for my bad english... Wenn es hier Deutsche gibt, Immer wenn ich in den Maschinenraum Gehe und die Geswindigkeit ändere Kommt ein Bluescreen und der komplette PC schmiert ab. Zudem gibt es eine Möglichkeit durch die Shotten zu gehen, ich muss mich immer mit F2 darumarbeiten

06-03-11, 08:32 AM	#2
Gerald SUBSIM Newsman Join Date: May 2008 Location: Close to sea Posts: 24,254 Downloads: 553 Uploads: 0	Welcome to Subsim f6l913! __________________ Nothing in life is to be feard,it is only to be understood. Marie Curie

06-03-11, 09:04 AM	#3
Bakkels Seasoned Skipper Join Date: Jan 2011 Location: Groningen, The Netherlands Posts: 709 Downloads: 101 Uploads: 6	What are your system specs? Because FM Interior is quite a demanding mod. 3 or 4 gig memory is recommended for this one. Also, there is a free camera mod so you don't have to press f2 when you want to walk around the ship, but I'm not exactly sure where I found it. Try searching the downloads section for that one. __________________ My sh3 skins : http://www.gamefront.com/files/user/Bakkels Or go to the sh3 downloads section > skins

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

06-03-11, 11:07 AM	#4
Fish In The Water Prince of the Sea SUBSIM Welcome Committee Join Date: Jul 2009 Location: Watching over U-253 Posts: 3,527 Downloads: 98 Uploads: 2	If you're running other (memory) 'heavy' mods, you might want to temporarily disable them and then try to replicate the issue with New Interiors. Also, there are a number of 'fixes' available that make other mods compatible with NI, so you may want to check your mod list and see if there are any potential conflicts. Aside from that, Bakkels is quite correct in suggesting you may need the 4 GB patch (along with the corresponding amount of RAM) in order to successfully run it. Good luck!