SUBSIM Radio Room Forums



SUBSIM: The Web's #1 resource for all submarine & naval simulations since 1997

Go Back   SUBSIM Radio Room Forums > Silent Hunter 3 - 4 - 5 > Silent Hunter 4: Wolves of the Pacific
Forget password? Reset here

Reply
 
Thread Tools Display Modes
Old 04-20-10, 08:39 AM   #1
Phantom II
Electrician's Mate
 
Join Date: Jan 2006
Posts: 139
Downloads: 33
Uploads: 0
Default SH4 Repair Crews

So I just started playing SH4 with TMO. While I was out on my first patrol, I got attacked by a Jap plane and took some pretty bad damage. I put a team on damage control, but they don't seem to be fixing anything? I've waited for about 4 days under time compression, and the priority list is just the same as it was when I left it. Is there some sort of trick to it?
__________________
Phantom II is offline   Reply With Quote
Old 04-20-10, 09:05 AM   #2
tomoose
Grey Wolf
 
Join Date: Aug 2005
Posts: 930
Downloads: 23
Uploads: 0
Default Repair screen

I'm assuming you mean you've physically dragged crew members into the damage control spots. You may need to fill all the spots depending on the damage. If you've done that then they will be working on the damaged parts. Go to your sub status screen (the tab with the cogs on it) and you'll see all the damaged parts in red (and your sub damage percentage in the upper left which IIRC if over 90 means you're basically SOL). In the bottom center should be a 'list' of the parts being repaired by priority with each one having a little 'bar' on the right side. If you mouseover this 'bar' it should display a number ratio. This should change if the part is being fixed.

Make sure you are not on silent running as the damage control won't do anything if silent running is on.

Lastly, it could be that your sub is simply too damaged to repair. Post a screenshot of your sub status screen and your crew status screen. This will help to nail down the problem.
good luck.
tomoose is offline   Reply With Quote
Old 04-20-10, 09:07 AM   #3
BillBam
Watch Officer
 
Join Date: Mar 2010
Location: Yuba/Sutter, CA
Posts: 347
Downloads: 171
Uploads: 0
Default

Are you running silent? Have you called crew to "repair stations?" Is the damage of the type that needs you to be surfaced and you are not? Just a few thinks I could think of that would prevent the repair happening.
BillBam is offline   Reply With Quote
Old 04-20-10, 09:58 AM   #4
Phantom II
Electrician's Mate
 
Join Date: Jan 2006
Posts: 139
Downloads: 33
Uploads: 0
Default

Silent Running is off, and the damage control crew is full. We're on battle stations and I have enabled the damage control team. Seems like a bug :/
__________________
Phantom II is offline   Reply With Quote
Old 04-20-10, 12:31 PM   #5
TH0R
XO
 
Join Date: Jul 2009
Location: Croatia
Posts: 420
Downloads: 52
Uploads: 0
Default

Maybe the damage is irreparable? If the compartment / equipment is fully red...
__________________
My IL2 stuff: LEVEL BOMBING MANUAL v2.0 | 'MUSTANG'
TH0R is offline   Reply With Quote
Old 04-20-10, 01:15 PM   #6
Excelsior82
Seaman
 
Join Date: Apr 2010
Location: Sens, France
Posts: 31
Downloads: 11
Uploads: 0
Default

I also noted some glitches when it comes to repair deck gun or flak. These can be marked as damaged but aren't in fact.

To correct this, I take control of the flak/gun for a few seconds and I suddenly get a message about it's repaired now.

Stranger, after a save/load, it can be marked damaged back

Maybe you can screenshot the damage control view to enable us telling you why it may not be repaired ?
Excelsior82 is offline   Reply With Quote
Old 04-21-10, 08:54 PM   #7
Armistead
Rear Admiral
 
Join Date: Dec 2008
Location: on the Dan
Posts: 10,880
Downloads: 364
Uploads: 0


Default

Another bug that often happens like the CO2 bug is your men will not go into repair mode. If you have damage in a compartment and on battlestations, place your mouse over the men in the compartment, they should list as repairing. If they list as on stations, they're not fixing. You just have to save and reload to clear the bug out. Happens more if you save a lot or tab out a lot...
Armistead is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:38 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © 1995- 2025 Subsim®
"Subsim" is a registered trademark, all rights reserved.