Adapted ARB WideGUI 1920x1080 v0.4 for Onealex V2

[Topo65]

Hello everyone. I am having this problem. It occurs when I try to install "CapZap1970 - ARB WideGUI 1920x1080 v0.4 for Onealex V6 mod" on "Onealex 1.52". I have followed the installation instructions step by step, but I can't seem to find the solution.

[CapZap1970]

Originally Posted by Topo65

Hello everyone. I am having this problem. It occurs when I try to install "CapZap1970 - ARB WideGUI 1920x1080 v0.4 for Onealex V6 mod" on "Onealex 1.52". I have followed the installation instructions step by step, but I can't seem to find the solution.

What seems to be the problem? More detailed info would be very helpful...

[Doolar]

I had initial problems when I first activated CapZap's ARB v6. The original GUI loaded but not CapZap's ARB mod v6. I do think it was a late nite error on my part. But maybe not. What happened was I activate CapZap's ARB v6 without the newly patched SH3.exe. I messed around with this a bit to no success. To fix this I :

1. de-activated v5, of course and deleted it from my SH3 MODS folder
2. I copied an original SH3.exe file from a backup copy of OneAlex 1.52 to my playable OneAlex 1.52 install, game folder.

Then I started over, following CapZap's instructions on patching and activating CapZap's ARB v6, and presto, it loaded and tested perfectly. Now I repeat. I think I messed things up on my end, at first by activating CapZap's ARB v6 without the patched SH3.exe. Dont't know if it did anything, but CapZap's ARB v6 was not loading. Not wanting to waist another 30 minutes with restarts and troubleshooting, I did the above. It took all but 10 minutes to fix and get back to sea.

[Topo65]

Originally Posted by CapZap1970

What seems to be the problem? More detailed info would be very helpful...

Of course. If you click on the image, you will notice that the text and background textures are misaligned. Something similar happens with the notepad in the attack periscope. If I try to use the rangefinder, the measurement line does not appear on the lens and the text on the notepad extends beyond the limit.

Megamod Onealex 1.52 works fine. The problem comes when trying to add this UI to it.

[Topo65]

This is the problem I have described above....

[CapZap1970]

That is strange, very strange, since nobody else had that problem.... look at the screenshots in the first post...

[Rod999]

Originally Posted by CapZap1970

That is strange, very strange, since nobody else had that problem.... look at the screenshots in the first post...

I have the same problem. No range finder in the lens and text if off to the right when clicking on range or speed in the notepad.

[CapZap1970]

There is something you are not doing right in the process...
Take a look at these fresh screenshots right out the oven just to show everything runs smoothly.... Just downloaded the mod again, installed it following the instructions, enabled it via JSGME and there you go...

[Topo65]

Ok. Evidently it is a problem with my setup or my instalation. If I find the solution, I will come back in case someone else has the same thing.

Anyway, thank you very much for your attention.

[CapZap1970]

Originally Posted by Topo65

Ok. Evidently it is a problem with my setup or my instalation. If I find the solution, I will come back in case someone else has the same thing.

Anyway, thank you very much for your attention.

All I can do is give you a couple of advises:
1.- Download again the ARB mod (just in case)
2.- While in the set up process, take your time and don't rush to avoid mistakes reading the Readme file step by step.


With that, for sure you will do it successfully!

[Rod999]

Originally Posted by Topo65

Ok. Evidently it is a problem with my setup or my instalation. If I find the solution, I will come back in case someone else has the same thing.

Anyway, thank you very much for your attention.

From what I found out, the notepad problem is caused by the option "Disable hardcoded scopes reticle" included in the automatized Tycho v3 SH3 Patch. Just don't patch nor move the sh3.exe file from the main folder. The Onealex mod has the parameters for widegui already integrated. Just activate the CAP mod with the data file only. Worked for me. Simple as that. - Even though I don't use the notepad, I like everything working properly.