![]() |
SUBSIM: The Web's #1 resource for all submarine & naval simulations since 1997 |
|
![]() |
#1 |
Navy Seal
![]() Join Date: Feb 2005
Location: York - UK
Posts: 6,079
Downloads: 43
Uploads: 0
|
![]() I doubt it is the CPU because I can't see how that would cause the VDDC error in the GPU. My suspicion is that the VDU has become defective. I have sent it off for testing as it is under warranty.
__________________
![]() |
![]() |
![]() |
![]() |
#2 |
Navy Seal
![]() Join Date: Jun 2008
Location: Land of windmills, tulips, wooden shoes and cheese. Lots of cheese.
Posts: 8,467
Downloads: 53
Uploads: 10
|
![]()
Fair enough, but you mention the board doesn't even beep a code. Removing a dead graphics card should let the board function normally, unless the circuitry to the PCI-E slot is toast. Considering you got a new board, this is highly unlikely.
Board that does nothing = dead CPU in my experience. Even a dead battery should normally let the system boot, but with a "bad checksum" error, notifying of a reset of BIOS settings.
__________________
Contritium praecedit superbia. |
![]() |
![]() |
![]() |
#3 |
Rear Admiral
![]() Join Date: Mar 2005
Posts: 13,224
Downloads: 5
Uploads: 0
|
![]()
Have you tried re-seating the CPU (take it out and re-install it) and making sure the cooling equipment is properly seated as well?
__________________
Follow the progress of Mr. Mulligan : http://www.subsim.com/radioroom/showthread.php?t=147648 |
![]() |
![]() |
![]() |
#4 |
Navy Seal
![]() Join Date: Feb 2005
Location: York - UK
Posts: 6,079
Downloads: 43
Uploads: 0
|
![]()
Yer, I moved the CPU when I tried the other MB.
I found out why there is no post beep. After *lots* of googling I managed to find out that it signals the end of the post tests via a light and not a beep unless I plug in my own speaker for postbeep. Gah! At least I can confirm it's a GPU issue now. Post light flashes fine except with the GPU in. Wonder what the new MB will get on ebay... ed: It's depressing seeing how far the value of my kit had sunk in less than a year.
__________________
![]() |
![]() |
![]() |
![]() |
#5 |
CINC Pacific Fleet
Join Date: Sep 2003
Location: Down Under
Posts: 34,807
Downloads: 171
Uploads: 0
|
![]()
What a bummer Letum, you should have done what CaptainHaplo suggested on the second post and removed all boards and drives, then power up, this would or should have produced some post beeps.
![]() Oh well, hopefully you get most of your money back, otherwise if the new board is better use that and sell the old one! ![]()
__________________
Sub captains go down with their ship! |
![]() |
![]() |
![]() |
#6 | |
Navy Seal
![]() Join Date: Feb 2005
Location: York - UK
Posts: 6,079
Downloads: 43
Uploads: 0
|
![]() Quote:
No post beeps because I was looking for sounds, not lights.
__________________
![]() |
|
![]() |
![]() |
![]() |
#7 |
CINC Pacific Fleet
Join Date: Sep 2003
Location: Down Under
Posts: 34,807
Downloads: 171
Uploads: 0
|
![]()
Oh well!!
![]() ![]()
__________________
Sub captains go down with their ship! |
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | |
|
|