Wooden Veneer Absolute / Relative / AOB Dial

Lancezh · 03-22-19, 12:53 PM

I totally remembered that i have access to an amazing Laserengraver and some really nice material, so i figured why not cut some tools for Wolfpack since i'm playing it quite a bit so i made this and it works really awesome i just had to share:

It's 200mm in diameter and cut with Maple Veneer

Here's a small youtube video:

Works completely without hinges and has almost no wiggle room so it's pretty accurate, easy to use.

Platapus · 03-22-19, 02:54 PM

How did you put the markings on?

Pisces · 03-22-19, 05:06 PM

In discord Wolfpack General channel he showed pictures of the intermediate laser burn phases. He used a "SPeedy 300 from trotec"

Lancezh · 03-22-19, 07:00 PM

Exactly this has been done using an industry grade trotec laser engraver speedy 300 with a 60w lasertube.

Platapus · 03-23-19, 06:27 AM

Yikes. that's some impressive marking.

Technical question, why do you need three independent scales? Is the third to measure possible attack angles from an enemy?

Pisces · 03-23-19, 10:50 AM

The smallest disk has the AOB scale. See both sides going up to 180 degrees. So if you align the observed AOB, either port or starboard, against the relative bearing (direction of periscope/UZO/TBT) then you can figure the target course. (assuming own course was set with the middle disk beforehand)

rolandslaw · 04-01-19, 08:16 PM

Sir ::

Your work is absolutely incredible. Can u make them out of plastic? Are u going to offer them for sale? If so, I want one:<)

I made one out of .. I think it was thin card board.... I used it in SH5. I can not find it nor can I find the instructions I followed to make it..... I think ... it has been at least two years.... I made clean copies of a disk from online and cut to size.... secured in the center with a file folder pin so as to allow the wheels to move freely.... not any where near the quality of yours:<)

Roland

Lancezh · 04-02-19, 03:28 AM

Hi Roland, i will make an Acrylic Version tonight and see how it turns out! But yeah definitely can be done, just need to adjust how the material is being engraved but that's about it.

03-22-19, 12:53 PM	#1
Lancezh Seaman Join Date: May 2012 Posts: 39 Downloads: 9 Uploads: 0	Wooden Veneer Absolute / Relative / AOB Dial I totally remembered that i have access to an amazing Laserengraver and some really nice material, so i figured why not cut some tools for Wolfpack since i'm playing it quite a bit so i made this and it works really awesome i just had to share: It's 200mm in diameter and cut with Maple Veneer Here's a small youtube video: Works completely without hinges and has almost no wiggle room so it's pretty accurate, easy to use. Last edited by Lancezh; 03-29-19 at 01:51 PM.

03-22-19, 02:54 PM	#2
Platapus Fleet Admiral Join Date: Oct 2006 Posts: 19,388 Downloads: 63 Uploads: 0	How did you put the markings on? __________________ abusus non tollit usum - A right should NOT be withheld from people on the basis that some tend to abuse that right.

03-23-19, 06:27 AM	#5
Platapus Fleet Admiral Join Date: Oct 2006 Posts: 19,388 Downloads: 63 Uploads: 0	Yikes. that's some impressive marking. Technical question, why do you need three independent scales? Is the third to measure possible attack angles from an enemy? __________________ abusus non tollit usum - A right should NOT be withheld from people on the basis that some tend to abuse that right.

04-01-19, 08:16 PM	#7
rolandslaw Bosun Join Date: Jun 2013 Posts: 66 Downloads: 66 Uploads: 0	tool Sir :: Your work is absolutely incredible. Can u make them out of plastic? Are u going to offer them for sale? If so, I want one:<) I made one out of .. I think it was thin card board.... I used it in SH5. I can not find it nor can I find the instructions I followed to make it..... I think ... it has been at least two years.... I made clean copies of a disk from online and cut to size.... secured in the center with a file folder pin so as to allow the wheels to move freely.... not any where near the quality of yours:<) Roland

03-22-19, 05:06 PM	#3
Pisces Silent Hunter Join Date: Dec 2004 Location: AN9771 Posts: 4,904 Downloads: 304 Uploads: 0	In discord Wolfpack General channel he showed pictures of the intermediate laser burn phases. He used a "SPeedy 300 from trotec"

03-22-19, 07:00 PM	#4
Lancezh Seaman Join Date: May 2012 Posts: 39 Downloads: 9 Uploads: 0	Exactly this has been done using an industry grade trotec laser engraver speedy 300 with a 60w lasertube.

03-23-19, 10:50 AM	#6
Pisces Silent Hunter Join Date: Dec 2004 Location: AN9771 Posts: 4,904 Downloads: 304 Uploads: 0	The smallest disk has the AOB scale. See both sides going up to 180 degrees. So if you align the observed AOB, either port or starboard, against the relative bearing (direction of periscope/UZO/TBT) then you can figure the target course. (assuming own course was set with the middle disk beforehand)

04-02-19, 03:28 AM	#8
Lancezh Seaman Join Date: May 2012 Posts: 39 Downloads: 9 Uploads: 0	Hi Roland, i will make an Acrylic Version tonight and see how it turns out! But yeah definitely can be done, just need to adjust how the material is being engraved but that's about it.