So what am I doing wrong? A mod question.

[Vacillator]

I'm using SH3 Commander, GWX and a few other mods which seem to work fine, like for example the white wave tops (apologies I can't remember who did it). For the 'extras' I used JSGME to install.

Just recently though I've added the open hatch mods discussed recently and the lowered antennas mod in the same way, but they don't seem to have worked. They show up in JSGME as enabled but no joy in game. Is there something obvious I should have done or that I've missed? They weren't installed in port, but I thought they would be okay anywhere?

Any help appreciated.

[melnibonian]

Are you sure you have the correct folder structure? The structure should be

C\Program Files\Ubisoft\GWX\MODS\Mod1\Data etc

and not

C\Program Files\Ubisoft\GWX\MODS\Mod1\Mod1\Data etc

Also since you did not add them while in port you're tempting fate. My suggestion would be to go to port, disable them, rollback SH3Cmd and then enable them. That should work.

[Vacillator]

I did quickly check the file structure and it looked okay but I see what you mean and will check again.

Otherwise it's back to port after my current rather long trip to CF99 (in a Type VIIB) for a re-install.

Thanks for the advice

[melnibonian]

Not a problem mate. I really hope you get yourself sorted

[danlisa]

Originally Posted by Vacillator

They weren't installed in port, but I thought they would be okay anywhere?

Any help appreciated.

That is never a good idea. I'm sure that the mods you have enabled require you to be in port before/after a patrol.

Did you also roll back SH3Cmdr before activating any mods. This is a must.

Mel has given you the first step, check the folder structure to make sure you have not got an extra folder.

I know it's going to be a pain but if you enabled these mods while at sea and didn't roll back SH3Cmdr then I would suggest a reinstall, you'll only experience problems later down the line. Frankly, I'm surprised your game even loaded.

Good Luck

[Vacillator]

Hmmm, thanks for that. I think I committed two sins here , I wasn't in port and possibly didn't roll back SH3Cmdr either! Having said that, yesterday as an afterthought I disabled the mods in JSGME, rolled back SH3Cmdr, re-enabled them then started via SH3Cmdr. But still not in port (doh!).

Anyway, maybe due to luck I'm still loading up okay! So I'll continue with the patrol and see what I can do back at Willi next time. As the mods are in my category of 'that would be nice' rather than 'necessity' like GWX it's not really a show-stopper.

So just to check my idiot's understanding of what I should do with any mod:
1. wait until port
2. roll back SH3Cmdr
3. install mod with JSGME if poss
4. run SH3Cmdr again
5. sail off into the sunset.
Am I okay with that procedure?

Also, should I have been running SH3 via SH3Cmdr every time? I guess not as it says at the bottom of the first screen 'loaded via SH3Cmdr' even when I've loaded by clicking SH3.exe. In which case I only need to run SH3Cmdr every time in port?

So many questions which I'm sure I must have read about, so my apologies!

[Rasher]

Hi guys

I have the same problem as Vac and having checked my file structure im even more confused now. Mel says that it should read C\Program Files\Ubisoft\GWX\MODS\Mod1\Data etc. My folder structure is different. It reads C\Program Files\Ubisoft\SilentHunterIII\Mods. The Mod folder contains all the JSGME Mods and that is where the Open Hatch Folder was copied to. Is this incorrect as im new to modding? Im using GWX with SH3 Cmdr 2.7 and GWX Skin pack with few other mods. Any help would be appreciated thanks.

Rasher

[danlisa]

Originally Posted by Vacillator

So just to check my idiot's understanding of what I should do with any mod:
1. wait until port
2. roll back SH3Cmdr
3. install mod with JSGME if poss
4. run SH3Cmdr again
5. sail off into the sunset.
Am I okay with that procedure?

That is exactly what you should do.

Originally Posted by Vacillator

Also, should I have been running SH3 via SH3Cmdr every time? I guess not as it says at the bottom of the first screen 'loaded via SH3Cmdr' even when I've loaded by clicking SH3.exe. In which case I only need to run SH3Cmdr every time in port?

So many questions which I'm sure I must have read about, so my apologies!

Everytime you use the 'Start SH3' button in SH3Cmdr the random parts of the program get changed and added to you game, things like malfunctions, random tracks etc.

Personally, I only use SH3Cmdr to load SH3 after I have finished a patrol, that way I'm likely to get a different set of files added, which makes the game a little more unpredictable. It also means that certain things don't get changed while I'm on patrol.

However, you are right, the settings applied by SH3Cmdr will remain active until you 'Rollback', lol, which is why it's important to do so when adding/deleting/enabling/diableing any mods.

[Rasher]

Hi again guys

I appalogise if i appeared to but in on this post, it was never my intention. Cheers

Rasher

[danlisa]

Originally Posted by Rasher

Hi again guys

I appalogise if i appeared to but in on this post, it was never my intention. Cheers

Rasher

No problem at all mate.

The location of your MODS folder is correct.

What Mel was saying is that you make sure that during the unzipping/extraction of your downloaded mods an extra folder is not created.

Mods should look like this.....(once inside the MODS folder)

Best Mod Ever > data > etc etc

NOT

Best Mod Ever > Best Mod Ever > data > etc etc