SUBSIM: The Web's #1 resource for all submarine & naval simulations since 1997 |
|
04-05-23, 11:31 AM | #1 |
Ocean Warrior
|
Here's one for Neal in 1/350th scale.
https://www.ebay.com/itm/351773047015
Its the Bronco SSN-21 Seawolf and not in 1/700th scale. This kit has been mostly impossible to find in North America for the last 10-15 years unless you wanted to pay an arm and a leg. I'm guessing they found some cardboard boxes full of kits in a Chinese warehouse. Neil, you need one of these. Park it next to your Ohio. For the rest of you, take note of the shipping times. I just ordered one with free shipping and its due to arrive sometime in August. Still, I've been trying to track this kit down for many years. Four more months won't make any difference. |
04-08-23, 10:12 AM | #2 |
Born to Run Silent
|
Thanks! I got the last one from that order.
__________________
SUBSIM - 26 Years on the Web |
05-03-23, 02:29 PM | #3 |
Ocean Warrior
|
So, my order showed up early.
Who says this forum doesn't have a world-wide reach? This kit is a nice little enigma, and has always been pretty rare. The kit is pretty basic. There are the two hull halves (in case you were wondering, yes, its a Bronco alright). Still, the fit will need some work but it is better than their Ohio class. You also get another sprue with parts for the sail, shrouded pump jet thig-a-majig, bow and stern planes, masts, and a two-piece stand. For the masts, you get two scopes, two radio masts, a snorkel, and the "mystery mast" which Bronco thought was a Soviet-era radar. There are also "leopard spot" decals for the scope and radio fairings. There is no photo-etch and all of the plastic is black. The scale looks good so far although the top of the sail is mostly set up for an "on the surface" look and also looks a little flat. Its a Bronco and they really should have launched a line of sand paper, files, and putty. As far as how old this kit is, that's where the "enigma" stuff starts to kick in. Dates on the box, instructions, and decals fall somewhere between 2009 and 2018 and Bronco has a habit of "re-poping" their molds every couple of years, so your guess is as good as mine. One nice touch on this kit is a "for sale only in mainland China" stamp inside the box. The decals are sealed and look to be in good condition. You get marking options for SSN-21 and SSN-22 plus the dreaded DSRV markers and full scope and antenna fairing details. Surface details and panel lines- This is NOT a Hobby Boss kit, it comes from an earlier generation which means that you'll want to have a good scriber and some thick surfacer on the shelf. There is, however, a very thin scribed water line to separate the top and bottom colors on the hull. Someone got confused on the stern planes and rudders. The stern planes are smooth while the rudders have a scribed "hinge line". The bow dome has no "break line" with the hull, so defiantly measure three times before you paint it. One thing I still want to check, the bow dome should be pretty close to the width of the bow on the Ohio kit and the bow dome on the Ohio kit has always bugged me. At this price point (while the supply lasts) , you may want to pick up a couple Seawolfs if you want to build the SSBN and hack off the domes of both kits. Minor stuff- The fixed cleats on the hull are molded as blobs but they can easily be filed off and replaced with some shirt pins. Decals are supplied for the wide array sonar on the hull, so double check which paint you want to use for the lower hull. The hull red isn't really right, I'm aiming more for (Tamiya) NATO Black with a solid black upper hull and sail and (Tamiya) Tire Black for the bow dome. So, its a Bronco and has its flaws BUT its quite in-expensive and best of all, its available again (at least for now). It should be an OK build for new modelers, especially if you want to learn how to file and fill seam lines. Otherwise, its still your ONLY shot at a Seawolf in 1/350th scale and what you get isn't that bad. Last edited by ET2SN; 05-03-23 at 02:55 PM. |
05-04-23, 06:48 AM | #4 |
Born to Run Silent
|
Mine came in, I need to fire up the modeling gene again
__________________
SUBSIM - 26 Years on the Web |
05-08-23, 12:38 PM | #5 |
Wayfaring Stranger
|
So what do you think? A fish tank full of clear resin with the model suspended in the middle or a surface diorama? Be cool to do a pier with it parked next to the Ohio. Be tough getting crew figures and dock accessories in such a small scale though!
__________________
Flanked by life and the funeral pyre. Putting on a show for you to see. |
05-08-23, 02:48 PM | #6 |
Ocean Warrior
|
There are several sources for 1/350th scale standing figures.
2D photoetch (pre-painted). I'm pretty sure Verlinden did this first but there are sets from several companies out there. 2D plastic. Tamiya and (I think?) Hobby Boss have sets available for WWII battleships. 3D printed plastic/resin. You can find multiple sets at Shapeways but I haven't ordered any, yet. Shapeways can be a great resource but they can also be a solid pain to order from. Keep in mind that a 1/350th scale standing figure is about the size of a small tick. I added a topside PO and a duty officer to my FLT III 688 many years ago and they're still hanging out. I glued their feet to the deck by dipping their shoes in some Elmer's Rubber Glue then quickly stuck them in position while the glue was still wet. The glue is thick enough to keep them standing tall until it dries and you don't have worry about the glue fogging the paint. With details this size, plan that you're going to lose at least one of them at some point. The rubber glue is easy to remove if this happens. Now that I think about it, the rubber glue would also work well if you're installing stuff like photo etch side rails and small antennas. Meanwhile, check that Ebay link in the first post if you're still on the fence about ordering it. As of today (5/8) there are still a butt ton of those kits available from mainland China. Last edited by ET2SN; 05-08-23 at 03:47 PM. |
Thread Tools | |
Display Modes | |
|
|