Lost Voice Commands Chief Engineer?

Lane · 01-29-09, 11:57 AM

For some Reason on my Last Patrol I lost the voice commands from the
Chief Engineer? I just get the text command message?
When I first Installed GWX 3 I had the Voice and Bell sounds when I would
change speed.? I hear all the other sounds inside the boat. and outside
on the Bridge. I am Running SH3 Commander 3.5 I ran a test using
Naval Academy Navigation Mission and still no sound from Engineer Officer
I just see him turn and speak and the text message.?
I hope is just a setting someplace?
Any:hmm: were to check?
Thanks for any help.
Lane

bigboywooly · 01-29-09, 12:19 PM

Have you altered any TC settings in SH3commander ???
Some settings can result in lost voices

Quote:

Since using SH3 Commander I can no longer hear speech or most sound effects.
This problem will occur if you set the "Character animations", "Sound effects" and/or "Particle
rendering" Time Compression events to 1. Reset each event back to the default value and try
again (a Rollback is not sufficient to reset these settings). If your problem persists, scrutinise any
new mods that you have installed since you last had full sound.

Lane · 01-29-09, 12:40 PM

Thank's bigboywooly

Yes I have been messing with the Time compression settings in SH3
Commander

Will set them back to defaut and test.
I think you hit the nail right on the head.

I had suspect I had messed up something with the SH3 Commander settings.

Thank's wooly will check things out.
Lane

Lane · 01-29-09, 06:01 PM

Thank's Wooly,

It worked

Change those Time compression settings to default.
and have all normal voice commands and Bells and hear code messages
from Radio Room.

Lane

FIREWALL · 01-29-09, 07:36 PM

Two asprins and gargle with salt water.

bigboywooly · 01-30-09, 08:42 AM

Cool
As long as fixed

01-29-09, 11:57 AM	#1
Lane Subsim Diehard Join Date: Jan 2002 Location: Southwest , Indiana USA Posts: 380 Downloads: 36 Uploads: 0	Lost Voice Commands Chief Engineer? For some Reason on my Last Patrol I lost the voice commands from the Chief Engineer? I just get the text command message? When I first Installed GWX 3 I had the Voice and Bell sounds when I would change speed.? I hear all the other sounds inside the boat. and outside on the Bridge. I am Running SH3 Commander 3.5 I ran a test using Naval Academy Navigation Mission and still no sound from Engineer Officer I just see him turn and speak and the text message.? I hope is just a setting someplace? Any:hmm: were to check? Thanks for any help. Lane

01-29-09, 07:36 PM	#5
FIREWALL Eternal Patrol Join Date: Mar 2006 Location: CATALINA IS. SO . CAL USA Posts: 10,108 Downloads: 511 Uploads: 0	Two asprins and gargle with salt water. __________________ RIP FIREWALL I Play GWX. Silent Hunter Who ???

01-30-09, 08:42 AM	#6
bigboywooly Rear Admiral Join Date: Apr 2006 Location: Swindon, England Posts: 10,151 Downloads: 35 Uploads: 0	Cool As long as fixed __________________ My mediafire page http://www.mediafire.com/?11eoq19bq9r41

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

01-29-09, 12:40 PM	#3
Lane Subsim Diehard Join Date: Jan 2002 Location: Southwest , Indiana USA Posts: 380 Downloads: 36 Uploads: 0	Thank's bigboywooly Yes I have been messing with the Time compression settings in SH3 Commander Will set them back to defaut and test. I think you hit the nail right on the head. I had suspect I had messed up something with the SH3 Commander settings. Thank's wooly will check things out. Lane

01-29-09, 06:01 PM	#4
Lane Subsim Diehard Join Date: Jan 2002 Location: Southwest , Indiana USA Posts: 380 Downloads: 36 Uploads: 0	Thank's Wooly, It worked Change those Time compression settings to default. and have all normal voice commands and Bells and hear code messages from Radio Room. Lane