Not sure if it is a problem. It's a new addition.
You can move it out of the way by pressing the tab beside the periscope up/down selector. This allows you to read the information on the notepad.

Hope this answers your question. Welcome on board.

edit: woops! Sorry, did not notice the missing green lamps.

Big thanks for invitation on board!!! :salute:

Yes, a little things missing - green lamps for I, II, III and IV torpedos :D

From the read me for TDC_Dials_Peri&UZO_V1.5

After SH4 start up, go to options, graphic settings and confirm that the resolution is at least 1280 x 960 or better.


I just reproduced your problem about 5 minutes ago, when I "forced" the resolution to 1024x768. I normally run at 1680x1050.

You won't belive me, but I just want to try higher resolutions :D

Problem solved by selecting higher resolution.
To tell the truth, in my own opinion, the best this game viewing at 1024x768.

The only thing needed to make an interface mod compatible with any resolution (and aspect ratio) is this part (in red):
Zone= 0 768 1024 768 2 1 0x0 0.5 -0.5 0x1E000000 -0.5 0.5 0 0.
I don't remember exactly what each setting ( 0 1, 1 1, 2 1 etc) did but it's not hard to find out. One of them is for stretching and the other for resolution scaling. FLB only used "0 0" that's why the basic placement and background panel only look good at one resolution.

Please, could someone point me where to find such skin for periscope:
http://img182.imageshack.us/img182/1299/peri1kr6.th.jpg

I mean with Siemens emblem :)

I've not seen any lifeboats for a while. Anyone else experiencing this? I've only played single missions so far with OMEGU. Maybe its just me:88)

I'm using OM 705
705-712
OMEGU v100
OMEGU patch 1
Real clothes v2

I have one thing that I have noticed, when the "R" key is pressed - depth under the keel - I get told 0. But when icon gets pressed the correct depth is shown.

Live Long and Prosper
Vince

omegu
 

Not sure about this small problem, since downloading omegu cannot seem to retreive saved games, they appear on the menu but when clicked on to play computer states that silent hunter has encountered a problem and needs to close and this is with games saved since installing omegu. Any ideas anybody.:cry:

You can not use any saved games after you install any MOD changes, except the one's where you are in port, HOME port.

U-boats type IIC and IID are downed after OMEGU_v100+OMEGU_v100_Patch1 installed.
They doesn't react to any assigned speed and propeller screw doesn't rotate.

Could someone else test this boats after OMEGU?

My Install:
OM_705->OM_705_712->OMEGU_v100->OMEGU_100_Patch1

Found out the same #1453

lurker_hlb3 has noticed.

OMEGU v100 Patch 2
 

Patch 2

Corrected PROPELLER ID mismatch in the Type II C/D

Corrected "Depth under the keel" command


http://www.subsim.com/radioroom/down...o=file&id=1274

The morale of the crew has greatly increased :D now that the rumors of heading back to port have been confirmed.

Thank you for the quick response with patch 2.

Having a wonderful time with your mod.:rock:

Live Long And Prosper
Vince

OMEGU v200
 

New version of OMEGU is up

Changes

Environment



V200 Changes

After further evaluation, the Atlantic sea color has become unacceptably (to green) and I have changed it to use the “Arctic” ocean color as the ATO baseline


Graphics



V200 Changes

Added elements of “Mikhail’s Hi-Res Submarines for NYGM 3” i.e.

New Hi-Res Skins for all Type II, VII, IX [less Type IXD2] and XXI.

German eagle added for type IIA & VIIB up until September 30th 1939

Per PM from Mikhail, Credit for Sub Skins go to Fubar and Graf

Full readme and download link in the first post

Nice work lurker on the new upgrade.

If I wanted to reverse the below, how would I go about doing it.

I have played around with it a bit but cannot figure it out :doh:

uninstall OMEGU
go to OMEGU_v200\Data\Menu
open menu.txt with wordpad
go to line 1211
change to

2110=N
2111=NNE
2112=NE
2113=ENE
2114=E
2115=ESE
2116=SE
2117=SSE
2118=S
2119=SSW
2120=SW
2121=WSW
2122=W
2123=WNW
2124=NW
2125=NNW

Thank you :yep::up:

i'm having problems with it too.

in game the only listed resolutions for me are:

1024 x 768 (@ various refresh rates)
1280 x 768 ( " " )
1360 x 768 ( " " )
1366 x 768 ( " " )

anything i can do to rectify this so i can get TDC_Dials_Peri&UZO_V1.5 to work properly?

can it be "forced" like in the C/documents/data/cfg/main folder?

just wondering...

thanks.