|
Quote:
MUCH faster than sorting by hand. Or you can use diff or some other diff program. I really wish the Mega Mods would use a diff/patch instead of replacing every file... -D |
Yep though i find it easier just to line them up side by side. The line searchers can be a bit screwy at times and not realy show you want your looking for (since the ones ive used compairs lines, not text strings). If i want to compare something specific i do a file search on both then compair the differences.
|
You might want to check and make sure this ID number [G3F I369] is not being used already. If it is, change it to the next available number.
|
Quote:
I do have a few more mods installed, but I don't think they affect the dials. |
Quote:
Do you think it will work for me? I use SH3, 1.4b upgrade, SH3CMDR. SH3Gen. I use three mods which might have an effect on it. They are DialsFdb2, Dials Mod V 1.2 and Improved Deck Compass V1.1 Also, is it possible to just put in the compass one, that is all I really need. |
It should work. The only problem is that because each mod adds new numbered locations it has to be installed by hand, and the proper numbers typed in for each segment of the mod.
As for just the compass, I don't see why not, but the downside is you would have to figure out exactly which segments to install and leave off the rest. Not easy, unless you're an expert, and I'm not. |
Yep and realy unless you already know those mods and what they change exactly, the only way to do it is the method i posted earlier.
As for your mods, Improved Deck Compass V1.1, SH3CMDR, SH3Gen, shouldnt cause a problem (the only one that might would be sh3 commander though i dont recall what exactly it mods in the game). These 2 will probably conflict DialsFdb2, Dials Mod V 1.2. as they likely overlap. If i was to ever incorporate that mod into my own personalized version of GW i would probably only do a half implimentation of just the expanded dials and the ability to mouse over the standard dials to make them pop up and discard the rest. As i am happy with my current setup of the text area, dials, etc. |
Quote:
I go to the periscope, raise it enough to see the number and point the scope where I want to go. Then I just hit = and the boat takes that course. It's accurate to within .5*. Too bad about the depth, but I find that +/- a meter or two is good enough most of the time. |
Yep though that workaround wont easily give you compass headings (as you have to calculate the bearing offset of the new course from the present), its often just easier to use the dial, or use the dial and then fine tune it with the periscope or uzo. Best solution of all would be as Dangerous Waters has it where you directly type in your course in degrees and depth.
|
i do not understand.my dials are clear and i use them easily without any mods...:hmm:
|
They are tiny though and can be hard to read or set precice courses or depths with
|
Yes I wonder if Ubisoft is working on another patch?? There are still some major things that could be redone like those mentioned above and also we need friggin map notes!! I am running out of notepad paper and my room is cluttered with notebook paper. I doubt that anyone from ubi will read this but it makes me feel better venting.
|
Highly doubtful there will ever be another patch. However , there is hope that many of the fixes will be implemented in SHIV and retrofitted for a re-release of SHIII; or that after SHIV there might be a new patch for SHIII.
|
So .. you're saying there's a chance.....!:)
|
A very small, tiny, teenie weenie, itsy bitsy, minute, little chance.
|
| All times are GMT -5. The time now is 12:18 PM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright © 1995- 2025 Subsim®
"Subsim" is a registered trademark, all rights reserved.