SUBSIM: The Web's #1 BBS for all submarine and naval simulations since 1997 
03302014, 02:57 PM  #16 
Watch
Join Date: Oct 2011
Location: Los Angeles
Posts: 21
Downloads: 14
Uploads: 0

For completeness, I list the procedural sequence that should be followed with the tables: (repeat for those who are interested, I can send you by email all tables for all relative bearings ad all LOS type)
Scenario: bearingonly TMA, track target with TA, ownship and target(submerged) in search phase. i) Measure the Br at time 2 and 4. (target range is decreasing or increasing?) ii) Recognize LOS type. (LAG, LEAD) iii) Whit the Br measured at time 4 and relative target bearing measured at time 2 > choose the corresponding table. (RelativeB+LOS+Br > Table) iv) Obtained the probable interval target range, seek a possible alignment of the points in the dotstack in the interval range. (Strip plotting) v) If the probability is friendly, the target will not be far from the solution found. Otherwise you will fall into the 5% probability that the interval be wrong. 
03302014, 03:49 PM  #17 
Silent Hunter

Sure, send them. Expect a pm.

04072014, 05:34 AM  #18  
Watch
Join Date: Oct 2011
Location: Los Angeles
Posts: 21
Downloads: 14
Uploads: 0

Quote:


12032017, 02:36 AM  #19 
Bilge Rat
Join Date: May 2017
Posts: 4
Downloads: 33
Uploads: 0

"About formula: (simple trigonometry)
With the law of sines you can calculate the angle § = arcsin( B/L*sin(w)) , w lower angle between B and bearing at time 0. B/L << 1 therefore § is approximately equal to §* = arctan(B/L) OR §* = arcsin(B/L) [error=<10^2] ''more easier to calculate''. In the example B is SpeedOwnship/60*2. For obtain L is sufficient bring the cursor on intersection of the bearings when the bearing appear on TMA display." Can someone explain how i get the angle w? Is it possibel to get the tabels for relative bearings and los typs? Regards Last edited by Seppel; 12032017 at 02:51 AM. 
12032017, 04:31 AM  #20 
Growing Old Disgracefully

A Warm Welcome To The Subsim Community > Seppel
Subsim <> Make A Donation <> See The Benefits <> Support The Community
__________________
LSH32015 <> TUTORIALS <> ALL YOU NEED TO KNOW <> ALL IN ONE PLACE SH4 <> TUTORIALS <> HOW TO DO IT <> INFORMATION <> DOWNLOAD LINKS SH5 <> TUTORIALS <> HOW TO DO IT <> INFORMATION <> DOWNLOAD LINKS Always Here To Help A Fellow 'Subber'  Need An Answer to A Question Just Send Me A PM 
12032017, 09:46 AM  #21  
The One and Only

Quote:
What is this formula in reference to? I just skimmed this thread briefly and didn't see anything.
__________________
Your friendly neighborhood modern submarine YouTuber! Also your Cold Waters sonarman **NEW** 688(I) Hunter/Killer Playthrough Cold Waters Playthrough All Dangerous Waters Videos This is my fault, but it's pronounced FPS chazly 

12052017, 01:13 AM  #22 
Bilge Rat
Join Date: May 2017
Posts: 4
Downloads: 33
Uploads: 0

If I understand correctly, the formula should determine a more accurate bearing rate. The formula is taken from an Italian tma manual (see link) I am looking for a decent method to get a better beraing rate, but so far without success. all selfdetermined beraing rates, for example, with the stopwatch are firstly inaccurate and secondly not suitable for a combat situation. other methods such as MoBo, in my opinion, ****. The general problem is the indication of opponent bearing. in all subsimgames I get, this is given as a whole number and not as a number with decimals.
We need a method with which we could determine the bearing rate relatively quickly after the first bearing. Maybe this formula is suitable? but I am still in the process of understanding them. Best regards 
12052017, 01:53 AM  #23 
Gefallen Engel U666

Seppel!
__________________
"Only two things are infinite: The Universe and human stupidity; And I'm not too sure about the Universe..." Philip K. Dick 
12052017, 08:02 AM  #24 
Bilge Rat
Join Date: May 2017
Posts: 4
Downloads: 33
Uploads: 0

<s> mate

Thread Tools  
Display Modes  

