No. The flares are not in GWX.
AO can be done in SH3.
Check the Subs by Wise to see how to do the AO.

I see

I have been told so :yep:

Okay, thanks, I will have a look into them later. I hope I got my file right. Maybe you can check it too :)

I will test several solutions in-game with your rock model.

Roger that.

Without my computer, I can already answer to this : Yes ! I already tried this issue by colliding the rock with my U-boot. The AI ships are also stuck if they are near the island. So, no need to have a .zon file with collision spheres ! But if you make this model a land unit, then you will have to create a .zon file with plenty of collision spheres, and this will require a lot of time.

Tried the reef out.
Put the .dat file in \Terrains\Locations folder.
Updated the Locations.cfg.

CTD.:hmmm:

Remapped id's in Silent3ditor

No more CTD.

Reef visible in game on surface (whether OnLand= true or false)

Nothing visible underwater.

And I drove straight through it.:o

Screenshot of result (L/H just me having a play)

Confirm that [except CTD]


inside reef:

http://www2.pic-upload.de/thumb/3259...2.9.55_740.jpg http://www2.pic-upload.de/thumb/3259....51.57_649.jpg http://www2.pic-upload.de/thumb/3259...5.52.41_86.jpg

underwater:

http://www2.pic-upload.de/thumb/3259....52.58_305.jpg


reef is transparent for light halos.

Yes, that's logical, because the base of the 3D model will always be placed on the sea surface if the model is placed from the Locations.cfg file. But the base should be placed on the sea bed if you create a new land unit and place it with the mission editor.

Strange ... :hmmm: If you try my work, you shouldn't be able to go through the island :

d/L link : http://www.mediafire.com/file/ky0fvj...Kendras_LH.zip

You will find :
- the 3D model : K_Lighthouse_1.dat
- an icon for the LH (maybe to improve a bit)
- a single mission : Test new LH.mis

It is JSGME ready. Put the folder k -- New lighthouses in your MODS folder and enable.

Before launching SH3, open the file data/Terrain/Locations.cfg (of your installation), and write this at the end (change ### with the correct number) :

[Location ###] ; test new lighthouse
Long=-4.755715
Lat=48.043404
Heading=90
OnLand=false
ShowOnMap=true
FileName=K_Lighthouse_1
LocationName=La Vieille

The problem doesn't come from gap's files. You have to edit the particles generators of the light halo, and change depth test from false to true IIRC. If you try my mod, you will see that you can't sea the lighthouse's light halo through the island.

About the rock, I would prefer a flat base from which some reliefs are emerging. Something like that, but smaller of course :

http://3.bp.blogspot.com/-CDILAfDwRs...600/export.jpg

Good tutorial here : https://www.darkcreations.org/hoddmi...hout-photoshop

Maybe it's due to the lack of the "Static object" controller, IIRC.

Had to delete Locations.cfg which came with mod as caused CTD (calls up bits and bobs that I don't have).
Edited my Locations.cfg as suggested, and all ran OK.

Nice model :salute:

The base extended beneath the surface of the sea (although placed using locations.cfg). I can confirm that it was solid when I tried to drive through) and that the light was not visible when it was behind another object.

I played around with settings in Gap's reef model (hope he doesn'tmind?). I found that by giving the Node-Reef1 Node Positioning Translation Y value a negative number (here -30 see 2nd screenshot) the model did go beneath the sea (see 1st screenshot of underwater view of sub)
I also tried changing the StaticObject parameters and setup to reflect yours but the boat still drove through.

Hope this helps.

All reminds me of this:-
https://www.youtube.com/watch?v=fscydKvocrw

"Negative Captain, I'm not moving anything."
:haha: :har:

I just don't understand the last sentence : "it's your call" ... ?

It means "It's up to you, alter course or ram a lighthouse!". Basically what we've been doing testing the mods - ramming lighthouses/rocks to see if they are solid or not!:D

To GAP
 

Hi Gap,

Tried PM'ing but your mailbox is full.

May have a fix for the drive through reef - added new node as child of existing node and moved 3d model, reflections below that. Possible that StaticObject describes a child object rather than an object at its own level????
Changed StaticObject type as well to 10/-1 and set squarelength to 200 (same as in Kendras' LH file) - not sure what that does though.

Any objections to me posting the changed file in this thread?

Regards,

MLF

Thank you for your feedback and sorry for the late replies guys. Yesterday and the day before yesterday I was on my way to home, and I had hardly the time to read your comments :)

Setting the reefs as land units is not strictly needed, especially if we find a way to anchor a terrain object to the seabed. Anyway in my own experience with SH5, even land or sea units can be made collisionable using the staticobject controller rather than collision spheres, just like terrain objects. IIRC the secret is putting the controller not directly on the main unit but on an equipment linked to it through eqp file. Though following the 3D profile of its parent unit, this collisionable equipment (can be a dummy, invisible copy of the reef) should not touch the main model in any point, otherwise some weird things can happen.

As usual :doh:

Possible. As I noted a few days ago, SHIII harbors stored in the Terrain/Locations folder, contain no actual 3D mesh, but only dummy placement nodes that Library 3D models, on turn, are attached to. Staticobject controllers are attached to Terrain/Locations files (one per file), rather than to library models. It is also possible that traslation values of placement nodes (rather than the ones of the nodes containing the 3D models) are used for determining the position of each model relative to the 3D world :hmm2:

Oh sorry, I had forgot setting controller's squarelength property after adding it, but the 10 / 1000 type controller container should be correct. IIRC I took it from one of the stock files

Yes, post it please. The more we are, the quicker we can sort bugs out :up:

So what's up with those CTD's? Are they Id-related or not? My dat file should not have duplicated Id's as I made it from scratch. I copy/pasted a few controllers with their parents from other files, but I am pretty sure I remapped all of them :hmm2: